International Journal of Urban Management and Energy Sustainability

International Journal of Urban Management and Energy Sustainability

Experimental Investigation of the Shear Strength Behavior of Two-Part Fiber-Reinforced Geopolymer Concrete Incorporating Hybrid PP/PVA Fibers

Document Type : Case Study

Authors
Department of Civil Engineering, Qa.C., Islamic Azad University, Qazvin, Iran
10.22034/ijumes.2026.746882
Abstract
The bond between existing concrete and a repair layer governs the load transfer and durability of repaired structures. Slag-based geopolymer repair materials are a lower-carbon alternative to Portland cement systems, but achieving adequate interfacial adhesion with old concrete remains a challenge. This study investigated how the nano-silica replacement level and particle size affect the interfacial bond of a slag-based geopolymer repair concrete reinforced with hybrid polypropylene and polyvinyl alcohol fibres. Ten mixtures combined NS replacement levels of 0%, 1%, 3% and 5% and nominal particle sizes of 8, 15 and 30 nm, at constant fibre contents of 0.5% PP and 0.5% PVA. Repair layers were cast on sandblasted Portland cement concrete substrates and tested at 28 days in 30° slant-shear and 90° direct-shear configurations; scanning electron microscopy and fracture surfaces were used to examine the interface. NS improved interfacial bond relative to the reference mixture, and the mixture with 3% NS of 8 nm performed best in both configurations. Increasing NS from 3% to 5% gave no consistent further gain, indicating an optimum governed by particle packing, binder reactivity and dispersion. Slant shear gave higher apparent bond resistance than direct shear owing to added normal compression, friction and interlock along the inclined interface. SEM revealed a compact repair matrix in intimate contact with the substrate, and failure shifted from predominantly interfacial separation towards mixed adhesive–cohesive failure, particularly in GPC3. Optimizing NS content and particle size can enhance the bond performance of hybrid-fibre geopolymer repair systems.

Graphical Abstract

Experimental Investigation of the Shear Strength Behavior of Two-Part Fiber-Reinforced Geopolymer Concrete Incorporating Hybrid PP/PVA Fibers

Highlights

·         Slag geopolymer repair concrete was modified with nano-silica and PP/PVA fibres.

·         Bond to existing concrete was tested in 30° slant-shear and 90° direct-shear setups.

·         3% nano-silica with 8 nm particles (GPC3-D8) gave the best interfacial bond.

·         Raising nano-silica from 3% to 5% gave no consistent further bond improvement.

·         Failure shifted from interfacial separation to mixed adhesive–cohesive failure.

Keywords

Ahmed, H. U., Mohammed, A. A., Rafiq, S., Mohammed, A. S., Mosavi, A., Sor, N. H., et al. (2021). Compressive strength of sustainable geopolymer concrete composites: A state-of-the-art review. Sustainability, 13(24), 13502. https://doi.org/10.3390/su132413502
ASTM International. (2022). Standard test method for pull-off strength of coatings using portable adhesion testers (ASTM D4541-22). https://doi.org/10.1520/D4541-22
ASTM International. (2024). Standard specification for concrete aggregates (ASTM C33/C33M-24a). https://doi.org/10.1520/C0033_C0033M-24A
Bayrak, B., Akarsu, O., Kılıç, M., Alcan, H. G., Çelebi, Ö., Kaplan, G., et al. (2024). Experimental study of bond behavior of geopolymer concrete under different curing conditions using a pull-out test. Construction and Building Materials, 439, 137357. https://doi.org/10.1016/j.conbuildmat.2024.137357
Cui, Y., Ai, W., Tekle, B. H., Liu, M., Qu, S., & Zhang, P. (2023). State-of-the-art review on the production and bond behaviour of geopolymer concrete. Discover Civil Engineering. https://doi.org/10.1007/s44242-023-00027-1
Hai, R., Ma, Z., Chen, X., Cao, Y., Zhang, J., & Hui, C. (2024). Experimental and numerical investigations on the bond-slip behavior of the interface between geopolymer concrete and steel tube. Scientific Reports, 14, Article 79964. https://doi.org/10.1038/s41598-024-79964-1
Li, J., Yang, L., Xie, H., Gao, J., Zhang, F., & Chen, S. (2025). Bond behavior between geopolymer recycled brick aggregate concrete and reinforcement: Pull-out test results. Construction and Building Materials. [Volume, article number and DOI to be completed by the authors]
Li, Z., Tan, J., Ouyang, J., Yu, Y., Li, S., Lin, T., et al. (2024). Experimental investigation of the bond performance at the interface between engineered geopolymer composites and existing concrete. Buildings, 14(6), 1819. https://doi.org/10.3390/buildings14061819
Liu, W., & Ju, S. (2024). Tunable thermal conductivity of sustainable geopolymers by Si/Al ratio and moisture content: Insights from atomistic simulations [Preprint]. arXiv. https://arxiv.org/abs/2401.11522
Luan, C., Wang, Q., Yang, F., Zhang, K., Utashev, N., Dai, J., et al. (2021). Practical prediction models of tensile strength and reinforcement-concrete bond strength of low-calcium fly ash geopolymer concrete. Polymers, 13(6), 875. https://doi.org/10.3390/polym13060875
Meskhi, B., Beskopylny, A. N., Stel’makh, S. A., Shcherban’, E. M., Mailyan, L. R., Shilov, A. A., et al. (2023). Analytical review of geopolymer concrete: Retrospective and current issues. Materials, 16(10), 3792. https://doi.org/10.3390/ma16103792
Niyazuddin, & Umesh, B. (2024). Experimental investigation on bond behaviour of the GFRP bars with normal and high strength geopolymer concrete. Construction and Building Materials, 429, 136395. https://doi.org/10.1016/j.conbuildmat.2024.136395
Özdemir, M. H. S., Bayrak, B., & Aydın, A. C. (2025). Bond performance of geopolymer concrete with basalt/glass fiber under elevated temperature. Engineering Structures, 324, 119368. https://doi.org/10.1016/j.engstruct.2024.119368
Prasad, B. V., Anand, N., Kanagaraj, B., Kiran, T., Lublóy, É., Naser, M. Z., Arumairaj, P. D., & Andrushia, D. (2023). Investigation on residual bond strength and microstructure characteristics of fiber-reinforced geopolymer concrete at elevated temperature. Case Studies in Construction Materials, 19, e02526. https://doi.org/10.1016/j.cscm.2023.e02526
Romanazzi, V., Leone, M., & Aiello, M. A. (2025). Bond performance of geopolymer concrete with steel and FRP reinforcements. Journal of Composites Science, 9(6), 303. https://doi.org/10.3390/jcs9060303
Skane, R., Schneider, P. A., Rickard, W. D. A., Jones, F., van Riessen, A., Jamieson, E., et al. (2025). Predicting the stability of geopolymer activator solutions for optimized synthesis through thermodynamic modelling [Preprint]. arXiv. https://arxiv.org/abs/2503.12942
Trabacchin, G., Sebastian, W., & Zhang, M. (2022). Experimental and analytical study of bond between basalt FRP bars and geopolymer concrete. Construction and Building Materials, 315, 125461. https://doi.org/10.1016/j.conbuildmat.2021.125461
Yuan, J., Xiao, J., & Huang, D. (2025). Experimental research on bond behavior of high-strength reinforcement in unconfined fly ash-based geopolymer concrete [Preprint]. SSRN. https://doi.org/10.2139/ssrn.5217139
Zarzuela, R., Luna, M. L., Carrascosa, L. M., Yeste, M. P., Garcia-Lodeiro, I., Blanco-Varela, M. T., et al. (2024). Producing C-S-H gel by reaction between silica oligomers and portlandite: A promising approach to repair cementitious materials [Preprint]. arXiv. https://arxiv.org/abs/2401.14118
 

  • Receive Date 05 April 2026
  • Revise Date 01 June 2026
  • Accept Date 02 July 2026